Transactions in the txpool are marked when another transaction
is seen double spending one or more of its inputs.
This is then exposed wherever appropriate.
Note that being marked with this "double spend seen" flag does
NOT mean this transaction IS a double spend and will never be
mined: it just means that the network has seen at least another
transaction spending at least one of the same inputs, so care
should be taken to wait for a few confirmations before acting
upon that transaction (ie, mostly of use for merchants wanting
to accept unconfirmed transactions).
22b51e06 db_lmdb: include chain height when failing to find an output key (moneromooo-monero)
5db433b3 blockchain: avoid exceptions in output verification (moneromooo-monero)
And optimize import startup:
Remember start_height position during initial count_blocks pass
to avoid having to reread entire file again to arrive at start_height
c867357a cryptonote_protocol: error handling on cleanup_handle_incoming_blocks (moneromooo-monero)
ce901fcb Fix blockchain_import wedge on exception in cleanup_handle_incoming_blocks (moneromooo-monero)
84fa015e core: guard against exceptions in handle_incoming_{block,tx} (moneromooo-monero)
If monerod is started with default sync mode, set it to SAFE after
synchronization completes. Set it back to FAST if synchronization
restarts (e.g. because another peer has a longer blockchain).
If monerod is started with an explicit sync mode, none of this
automation takes effect.
Hide DB types from db_types.h - no reason to recompile dependencies
when DB types change.
Also remove lingering in-memory DB references, they've been
obsolete since 9e82b694da
When scanning for outputs used in a set of incoming blocks,
we expect that some of the inputs in their transactions will
not be found in the blockchain, as they could be in previous
blocks in that set. Those outputs will be scanned there at
a later point. In this case, we add a flag to control wehther
an output not being found is expected or not.
The recent change to not keep separate track of the blockchain
height caused the reported height to jump early in the lmdb
transaction (when the block data is added to the blocks table),
rather than at the end, after everything succeeded. Since the
block data is added before the transaction data, this caused
the transaction data to be saved with a height one more than
its expected value.
Fix this by saving the block data last. This should have no
side effects.
This replaces the epee and data_loggers logging systems with
a single one, and also adds filename:line and explicit severity
levels. Categories may be defined, and logging severity set
by category (or set of categories). epee style 0-4 log level
maps to a sensible severity configuration. Log files now also
rotate when reaching 100 MB.
To select which logs to output, use the MONERO_LOGS environment
variable, with a comma separated list of categories (globs are
supported), with their requested severity level after a colon.
If a log matches more than one such setting, the last one in
the configuration string applies. A few examples:
This one is (mostly) silent, only outputting fatal errors:
MONERO_LOGS=*:FATAL
This one is very verbose:
MONERO_LOGS=*:TRACE
This one is totally silent (logwise):
MONERO_LOGS=""
This one outputs all errors and warnings, except for the
"verify" category, which prints just fatal errors (the verify
category is used for logs about incoming transactions and
blocks, and it is expected that some/many will fail to verify,
hence we don't want the spam):
MONERO_LOGS=*:WARNING,verify:FATAL
Log levels are, in decreasing order of priority:
FATAL, ERROR, WARNING, INFO, DEBUG, TRACE
Subcategories may be added using prefixes and globs. This
example will output net.p2p logs at the TRACE level, but all
other net* logs only at INFO:
MONERO_LOGS=*:ERROR,net*:INFO,net.p2p:TRACE
Logs which are intended for the user (which Monero was using
a lot through epee, but really isn't a nice way to go things)
should use the "global" category. There are a few helper macros
for using this category, eg: MGINFO("this shows up by default")
or MGINFO_RED("this is red"), to try to keep a similar look
and feel for now.
Existing epee log macros still exist, and map to the new log
levels, but since they're used as a "user facing" UI element
as much as a logging system, they often don't map well to log
severities (ie, a log level 0 log may be an error, or may be
something we want the user to see, such as an important info).
In those cases, I tried to use the new macros. In other cases,
I left the existing macros in. When modifying logs, it is
probably best to switch to the new macros with explicit levels.
The --log-level options and set_log commands now also accept
category settings, in addition to the epee style log levels.
3ff54bdd Check for correct thread before ending batch transaction (Howard Chu)
eaf8470b Must wait for previous batch to finish before starting new one (Howard Chu)
c903c554 Don't cache block height, always get from DB (Howard Chu)
eb1fb601 Tweak default db-sync-mode to fast:async:1 (Howard Chu)
0693cff9 Use batch transactions when syncing (Howard Chu)
m_num_outputs keeps track of the number of outputs, which should
be the same as the size of both the output_txs and output_amounts
databases. If one goes out of sync, we need to throw to abort
whatever it is we were doing.
Add consts in a few places where it makes sense, avoid unnecessary
memory reallocation where we know the full size needed at the outset,
simplify and avoid memory copy.
